Main equipment and telemetry signals in an LNG facility
An LNG facility has four main blocks: pretreatment, a liquefaction train, storage tanks, and loading or export. The liquefaction train holds the rotating equipment that reliability teams watch most closely: gas turbine drivers, refrigerant compressors, and heat exchangers.
What are the main process areas in an LNG facility?
Feed gas passes through pretreatment, liquefaction, storage, and loading, in that order. Each area has its own equipment and its own failure risks.
Pretreatment comes first. Cameron LNG describes removing dust, water, hydrogen sulfide, and mercury, then using an amine absorber for acid gas and an adsorbent for water. Heavy hydrocarbons (C5+) are removed by fractionation before liquefaction. Skipping these steps risks corrosion and freezing, especially in aluminum heat exchangers.
Liquefaction follows, in units called trains. According to a DOE fundamentals document, each train is a complete stand-alone processing unit, and plants usually build several side by side.
Storage and export complete the chain. The DOE environmental assessment for Sabine Pass lists refrigerant storage tanks, in-tank LNG pumps, recycle boil-off gas compressors, flares, and export by LNG carrier.
Mixed vendors across these areas complicate monitoring. The way anomaly detection across mixed OEM equipment breaks down is worth knowing before you compare signals between machines.
How does the liquefaction train work?
A train cools treated gas in stages with refrigerant circuits, driven by gas turbines and compressors. The gas ends up as liquid at about -162°C.
Gas Processing & LNG describes the C3MR process. A propane precooling cycle cools the gas and the warm mixed refrigerant to about -35°C. A mixed refrigerant cycle then liquefies and subcools the gas. Cameron LNG says the main cryogenic heat exchanger finishes the job.
Drivers and compressors set the pace. The same article says C3MR trains normally use two gas turbine drivers (30-MW Frame 5) per cycle, and each train has two compressors running at 50% capacity. Oman LNG states that the size of the compressors mainly determines a train's nominal capacity. In one Shell design discussed in an IPTC paper, production continues at 60% of train capacity if one liquefaction cycle trips.
Gas turbine-driven generators also appear at the site. The approach to monitoring power and cooling equipment in other facilities carries over to them.
Which signals show rotating equipment is degrading?
Watch the compressors, turbines, and their auxiliaries for trends, not just alarms. A slow drift against a healthy baseline at the same load usually warns earlier than a fixed limit.
| Equipment | Signals to trend | What a shift suggests |
|---|---|---|
| Refrigerant compressor | Shaft vibration, bearing temperature, suction and discharge pressure, flow | Rising vibration points to bearing wear or imbalance; falling discharge pressure at constant speed points to fouling or recycle leakage |
| Gas turbine driver | Exhaust temperature spread, vibration, speed, lube oil pressure and temperature | A widening exhaust spread suggests combustion problems; oil temperature creep suggests cooler or bearing trouble |
| Main cryogenic heat exchanger | Temperature approach, pressure drop, outlet temperatures | A growing pressure drop suggests blockage or icing from impurities |
| Cryogenic pump | Motor current, vibration, discharge pressure | Falling pressure with rising current suggests wear |
These signals come from general reliability practice. Set thresholds from each machine's own history and the OEM manual.
Which signals matter on LNG storage tanks?
Track temperature at several heights, tank pressure, liquid level, and density. Together they show stratification, boil-off, and leaks.
Rollover can occur when layers of different density form in the tank. A growing density or temperature difference between layers is the early sign. Rising tank pressure with a steady level points to more boil-off. A falling level with no matching outflow calls for an immediate check.
Boil-off gas goes to recycle compressors, per the Sabine Pass assessment, so trend their load alongside tank pressure.
Which safety and gas detection systems need monitoring?
Fire and gas detection and safety systems are part of each train. The Sabine Pass assessment lists them with the control systems in each train.
Monitor the health of the detection layer itself. A detector that reads a flat value for days, or drops out, may be failed rather than quiet. When a detector trips, read it next to nearby process readings to judge whether it is a real leak or a sensor fault.
Frequently asked questions
How many compressors does one train have?
It depends on the design. The Sabine Pass assessment describes six gas turbine-driven refrigerant compressors per train. Gas Processing & LNG describes a C3MR arrangement with two compressors per train.
Why does a train keep running if one cycle trips?
Some designs split the load across cycles. In the Shell design above, production is designed to continue at 60% of train capacity after one liquefaction cycle trips.
How do teams compare signals from different vendors?
They map each vendor's tags to one shared equipment model, so a compressor's vibration reads the same everywhere. If you want to build that model for your facility, start with one site and one goal.
Related resources
SailPlan builds the machine-readable data model that makes every AI tool in your stack actually work. Request a demo to see it in action.